Acrylic vs Glass

Acrylic vs glass which is better for your project Calsak Plastics

By B. Decker, Digital Content Specialist · Calsak Plastics · Published October 27, 2026 · Last updated October 27, 2026

Acrylic is half the weight of glass and 10 to 20 times more impact-resistant than ordinary plate glass. It also transmits slightly more light. Glass wins on scratch resistance, stiffness, heat tolerance, and fire performance. Choose acrylic where breakage, weight, or fabrication matter. Choose glass where heat, abrasion, or code-rated fire performance matter.

Key takeaways

  • At 1/4″ thick, acrylic weighs about 1.5 lb/ft² versus 2.9 lb/ft² for plate glass.
  • Acrylic’s falling-ball impact strength is about 18 times that of plate glass and comparable to tempered glass.
  • Glass is far harder. Uncoated acrylic scratches easily unless you specify an abrasion-resistant grade.
  • Acrylic is combustible. Check the building code before you replace glass with acrylic.

What Is the Difference Between Acrylic and Glass?

Acrylic is a plastic. Its chemical name is polymethyl methacrylate (PMMA), and it is also sold as plexiglass, Plexiglas®, ACRYLITE®, Perspex®, and Acrycast®. Window and display glass is usually soda-lime glass, an inorganic material made mostly from silica.

Both are clear, rigid, and used for glazing, displays, and enclosures. They behave very differently once you load them, heat them, scratch them, or drop them. That is where the choice gets made.Acrylic vs glass impact strength and weightAt one quarter inch thick, plate glass absorbs 1.0 ft-lb, tempered glass 15.5 to 29.1 ft-lb, and acrylic 18.1 ft-lb in falling-ball impact tests. Acrylic weighs 1.5 lb per square foot versus 2.9 for glass.Acrylic vs glass at 1/4 inch thickSource: ACRYLITE® acrylic vs glass property dataFalling-ball impact strength (ft-lb)01020301.0Plate glass15.5–29.1Tempered glass18.1AcrylicWeight (lb per sq ft)01232.9Glass1.5AcrylicAcrylic: about 18x the impact strength of plate glass at about half the weight.Calsak Plastics · calsakplastics.comFigure 1. Impact strength and weight of 1/4-inch acrylic, plate glass, and tempered glass. Data: ACRYLITE®.

Acrylic vs Glass at a Glance

PropertyAcrylic (PMMA)Glass (soda-lime plate)
Weight, 1/4″ sheetAbout 1.5 lb/ft²About 2.9 lb/ft²
Falling-ball impact, 1/4″18.1 ft-lb1.0 ft-lb (plate); 15.5–29.1 ft-lb (tempered)
How it breaksLarge pieces with duller edgesSharp shards (plate); small cubes (tempered)
Light transmissionAbout 92%About 89% at 6 mm (clear float)
Edge colorWater-clearGreen tint, deeper as thickness grows
Scratch resistance (Taber haze, 100 cycles)26.88% uncoated; 1.34% with abrasion-resistant coating0.23%
StiffnessLower; needs 1.5–2.5x the thickness for the same wind loadHigher
Thermal expansionAbout 8x glassLow
Max continuous service temperature160°F (extruded); 180°F (cast)Much higher
Insulation (thermal conductivity)1.3 BTU/(hr·ft²·°F/in)5.3 BTU/(hr·ft²·°F/in)
Fire behaviorCombustible thermoplastic (UL 94 HB)Non-combustible
FabricationSaw, rout, drill, laser, bend, and cement in-houseSpecialist cutting; can’t be drilled after tempering

Sources: weight, impact, stiffness, scratch, expansion, and conductivity values from ACRYLITE® acrylic vs glass properties. Service temperatures from ACRYLITE®. Glass light transmission from the Vitro Clear glass product data sheet. Acrylic light transmission from 3A Composites’ PERSPEX® Clear data.

Is Acrylic Stronger Than Glass?

Against impact, yes. In ACRYLITE’s falling-ball test, 1/4″ acrylic absorbed 18.1 ft-lb, compared with 1.0 ft-lb for 1/4″ plate glass and 15.5–29.1 ft-lb for tempered glass (ACRYLITE). That puts acrylic at 10 to 20 times the impact strength of plate glass and in the same range as tempered glass.

When acrylic does break, it cracks into large pieces with edges much less sharp than broken plate glass (ACRYLITE). That safer break pattern is a big reason acrylic is used for displays, sneeze guards, and glazing that people work close to.

Against bending, no. Acrylic has lower tensile strength and stiffness than glass. ACRYLITE notes that acrylic glazing usually needs 1.5 to 2.5 times the thickness of plate glass to handle the same wind load, and shelving needs at least 2.5 times the thickness to carry the same weight. If a panel must stay flat under load, size the acrylic thicker or add support.

Is Acrylic Clearer Than Glass?

Yes, slightly, and the difference grows with thickness. Clear acrylic transmits about 92% of visible light (3A Composites). Vitro rates its clear float glass at 89% at 6 mm (Vitro).

Glass also absorbs more light as it gets thicker, which is why thick glass edges look green. ACRYLITE’s data shows colorless acrylic absorbing essentially no visible light at every thickness listed, from 0.118″ to 0.750″, while plate glass absorbs more as it gets thicker (ACRYLITE):Light absorption of acrylic vs glass by thicknessPlate glass absorbs 2 percent of visible light at 0.118 inch rising to 11 percent at 0.750 inch. Colorless acrylic absorbs essentially 0 percent at every thickness.Visible light absorbed by sheet thicknessSource: ACRYLITE® typical values, colorless acrylic vs plate glass0%4%8%12%2%0%0.118″3%0%0.177″4%0%0.236″6%0%0.375″8%0%0.500″11%0%0.750″Plate glassClear acrylicCalsak Plastics · calsakplastics.comFigure 2. Plate glass absorbs more light as it gets thicker; colorless acrylic stays near zero. Data: ACRYLITE®.

For aquariums, display cases, and edge-lit signs, that water-clear edge is a visible advantage.

Weight, Handling, and Installation

Acrylic weighs about half as much as glass of the same size and thickness. A 4′ x 8′ sheet of 1/4″ acrylic weighs roughly 48 lb, compared with roughly 93 lb for plate glass, based on ACRYLITE’s per-square-foot figures. Lighter panels mean cheaper freight, fewer installers, and lighter framing.

Two installation rules change when you switch to acrylic:

  1. Leave room to move. Acrylic’s coefficient of thermal expansion is about eight times that of glass, and it also moves with humidity (ACRYLITE). Oversize the frame channel and slot the fastener holes.
  2. Size for stiffness, not just impact. Thicker sheet or extra supports keep large panels from bowing.

Scratch and Chemical Resistance

This is glass’s biggest advantage. In Taber abrasion testing, plate glass hazed only 0.23% after 100 cycles, while uncoated acrylic hazed 26.88% (ACRYLITE). An abrasion-resistant coated acrylic cut that figure to 1.34%.

Cleaning matters too. ACRYLITE recommends mild soap or detergent and lukewarm water with a soft cloth and light pressure. It warns against window-cleaning sprays, scouring compounds, and solvents such as acetone and alcohol, which can scratch acrylic or cause fine surface cracks called crazing (ACRYLITE care guide). Fine scratches can be removed by hand polishing with a plastic scratch remover; deeper ones need wet sanding and buffing. Glass scratches far less often in the first place.

Heat, Fire, and Building Codes

Glass tolerates far more heat than acrylic. ACRYLITE rates its extruded acrylic for continuous service from -30°F to 160°F and its cast acrylic from -40°F to 180°F (ACRYLITE). Keep acrylic away from heat sources such as ovens, fireplaces, high-wattage lamps, and heat lamps.

Acrylic is a combustible thermoplastic with a UL 94 HB flammability rating (ACRYLITE). In commercial buildings, the International Building Code regulates light-transmitting plastics under Section 2606, which sorts them into combustibility classes CC1 and CC2. Before substituting acrylic for glass in a wall, door, skylight, or partition, confirm what your local code allows.

Some acrylic sheet products are tested to safety glazing standards such as ANSI Z97.1. Compliance depends on the product and thickness, so confirm it on the manufacturer’s documentation for the exact sheet you buy.

Outdoor Use and UV

Acrylic weathers well outdoors. It is naturally UV-stable, and Röhm backs several clear ACRYLITE® products with a 30-year warranty against yellowing (ACRYLITE). For planning, a typical outdoor service life is 10 to 20 years, depending on the grade, color, and exposure. Unlike standard polycarbonate, acrylic does not need a UV-protective cap, which is one reason it is a staple for sign faces. Glass is heavy and breaks under impact, which limits it for large exterior signs.

When to Use Acrylic and When to Use Glass

ApplicationBetter choiceWhy
Aquariums, especially large or curved tanksCell cast acrylicLighter, impact-resistant, clear in thick sections, and can be formed
Picture framing and art glazingAcrylic (UV-filtering or non-glare grades)Half the weight and shatter-resistant for shipping and hanging
Retail displays, POP, store fixturesAcrylicEasy to fabricate, bond, and bend into shapes
Sign faces and edge-lit signsAcrylicClear edges, colors, and outdoor durability
Sneeze guards and protective barriersAcrylic (or polycarbonate for high impact)Safer break pattern, light to mount
Shelving under heavy loadsGlass (or thicker acrylic)Glass is stiffer at the same thickness
High-traffic surfaces such as tabletops and countersGlass or coated acrylicScratch resistance
Near heat: ovens, fireplaces, lampsGlassAcrylic softens with heat
Fire-rated assembliesGlass (rated)Acrylic is combustible

If a part takes hard, repeated impact, such as machine guards or vandal-prone glazing, look at polycarbonate instead. Our guide to polycarbonate sheets covers that trade-off.

Acrylic vs Glass for Aquariums

Large and custom aquariums are commonly built from cell cast acrylic. It is lighter than glass, more impact-resistant, and available in the heavy gauges big viewing panels need. Extruded acrylic is not made in those thicknesses. Acrylic scratches more easily, so clean it with a non-abrasive pad. Glass resists scratching from gravel and algae scrapers far better, as the Taber data above shows. Read why cell cast acrylic is required for aquarium-grade panels in our Acrycast technical guide.

Frequently Asked Questions About Acrylic vs Glass

Is acrylic stronger than glass?

Against impact, yes. One-quarter-inch acrylic has about 18 times the falling-ball impact strength of plate glass. Glass is stiffer, so acrylic needs more thickness to resist bending.

Is acrylic clearer than glass?

Slightly. Clear acrylic transmits about 92% of visible light, and clear float glass about 89% at 6 mm. Acrylic edges stay water-clear, while glass edges look green.

Is plexiglass better than glass?

It depends on the job. Plexiglass (acrylic) is better where weight, breakage, and fabrication matter. Glass is better for scratch resistance, heat, stiffness, and fire-rated uses.

Does acrylic scratch more easily than glass?

Yes. Uncoated acrylic is much softer than glass. For high-touch surfaces, specify an abrasion-resistant coated acrylic or use glass.

Is acrylic as strong as tempered glass?

In falling-ball impact testing, 1/4″ acrylic (18.1 ft-lb) falls inside tempered glass’s range (15.5–29.1 ft-lb). Tempered glass is stiffer and more heat-resistant.

Can acrylic replace glass in windows?

Often, yes, as long as you allow for thermal expansion and use enough thickness for the wind load. In commercial buildings, check IBC Section 2606 and your local code first.

Can I clean acrylic with a glass cleaner?

Usually not. ACRYLITE advises against window-cleaning sprays on standard acrylic because they can scratch or craze the surface. Use mild soap and lukewarm water with a soft cloth.

Is acrylic glass real glass?

No. “Acrylic glass” is a nickname for acrylic sheet, a plastic called PMMA. It is not made of silica like real glass.

Need Acrylic Cut to Size?

Calsak Plastics has supplied plastic sheet since 1972. We are the exclusive U.S. distributor of Acrycast cell cast acrylic, and we supply extruded acrylic for displays, glazing, and signs through seven U.S. branches. Cut-to-size orders typically ship in one to three days.

See our acrylic sheet options, explore Acrycast cell cast acrylic, or contact your local branch.

Sources

B. Decker, Digital Content Specialist at Calsak Plastics

About the author

B. Decker, Digital Content Specialist

B. Decker is a Digital Content Specialist working with Calsak Plastics, with five years of focused content production for the industrial plastics distribution sector and a decade of broader industrial-sector writing experience. B’s work covers materials science explainers, fabrication and machining guidance, specification support, and application case studies across thermoplastics, engineering plastics, and composites. Technical content is reviewed by Calsak’s applications and product management teams before publication.

Connect with B on LinkedIn

author avatar
B. Decker

Leave a Reply